If the tailgate won’t open, it’s likely because the tonneau cover is preventing it from doing so. In order to open the tonneau cover, you’ll need to first release the clamps that are holding it in place. Once the clamps have been released, you should be able to open the cover and then access the tailgate.
Broken tailgate handle with locked bed cover
- If the tonneau cover is attached to the tailgate and the tailgate won’t open, there are a few steps you can take to try and fix the issue
- Check to see if the tonneau cover is locked
- If it is, unlock it and try opening the tailgate again
- If the tonneau cover is not locked, try opening it from the inside of the vehicle
- If neither of those options work, there may be an issue with the latch or mechanism that connects the tonneau cover to the tailgate
- Try inspecting and troubleshooting that area to see if you can identify a problem
Tonneau Cover Without Opening Tailgate
A tonneau cover is a great way to keep your cargo safe and secure. But what do you do when you need to open the tailgate? Here’s a quick guide on how to open a tonneau cover without opening the tailgate.
1. First, locate the release lever or knob on the inside of the cover. This is usually located near the front or rear of the cover.
2. Next, pull the release lever or knob to disengage the locking mechanism.
3. Once the locking mechanism is disengaged, you should be able to lift up on the tonneau cover and open it like a door. Be sure to support the cover as you open it so that it doesn’t fall off and hit you in the face!
4. Finally, once you’ve opened up your tonneau cover, make sure to re-engage the locking mechanism before closing it again.
This will ensure that your cargo stays put while you’re driving down the road.
How to Open Truck Bed Cover Without Key
If you have a truck bed cover and lose your key, don’t worry! There are a few ways to open it without the key.
One way is to use a wire hanger.
Unbend the hanger so that you have a long, thin piece of wire. Then, insert the wire into the gap between the cover and the side of the truck bed. Move it around until you find the locking mechanism.
Once you find it, jiggle and wiggle until you unlock the cover.
Another way is to use a Slim Jim. If you don’t have one handy, you can make your own by using a strong piece of metal or plastic (a credit card will work in a pinch).
Just slide it between the cover and side of the truck bed until you find the locking mechanism and then pop it open!
If all else fails, you can always call a locksmith. They’ll be able to get into just about anything!
Tonneau Cover Latch Stuck
If you’ve ever had a tonneau cover latch become stuck, you know how frustrating it can be. The good news is that there are some things you can do to try and fix the problem.
First, make sure that the area around the latch is clean and free of debris.
Sometimes dirt or grime can build up around the latch and cause it to become stuck. If this is the case, simply clean the area and see if that solves the problem.
If the latch is still stuck, you may need to lubricate it with WD-40 or a similar product.
Just spray a bit onto the latch and then operate it a few times to see if that does the trick.
If neither of these solutions work, then your best bet is to take the cover off completely and inspect the latch mechanism. It’s possible that something inside has become damaged or broken and will need to be repaired or replaced.
This is usually not a difficult task, but it’s best to leave it to a professional if you’re not confident in your ability to do so.
How to Open Tailgate With Broken Handle
If you have a broken tailgate handle, there are a few ways that you can open your tailgate.
One way is to use a flat head screwdriver. Simply insert the screwdriver into the hole where the handle would normally go and push or pull until the tailgate opens.
Another way is to use a rope or bungee cord. Tie one end of the rope or cord around the latch on the tailgate, and then pull on the other end until the tailgate opens.
If you have neither a screwdriver nor a rope, you can try using a coat hanger.
Straighten out one end of the hanger and insert it into the hole where the handle would go. Then, wiggle and jiggle until the tailgate pops open.
Tonneau Cover Latch Broken
If you have a tonneau cover on your truck, you know how important it is to keep everything secure. But what do you do when the latch breaks?
Don’t worry, we’ve got you covered.
(pun intended)
First things first, you’ll want to assess the damage. If the latch is completely broken, you’ll need to replace it.
But if it’s just cracked or bent, it can usually be fixed with some elbow grease and a few tools.
Once you’ve determined what needs to be done, here are step-by-step instructions for fixing or replacing a broken tonneau cover latch:
If the latch is just cracked or bent:
1. Use a hammer to gently straighten out the metal piece.
2. Use pliers to bend any sharp edges back into place.
3. Test the latch to make sure it works properly before reattaching the cover.
If the latch is completely broken:
1.Remove the old latch by unscrewing it from the cover
2 .
Measure and cut a new piece of metal to size
3 .Bolt or screw the new piece in place
4 .
Credit: www.youtube.com
How Do You Open a Locked Tonneau Cover?
Locked tonneau covers are a great way to keep your belongings safe and secure while driving. However, if you accidentally lock your tonneau cover, don’t fret! There are a few ways you can open a locked tonneau cover.
One way to open a locked tonneau cover is by using a pair of pliers. Simply insert the tips of the pliers into the keyhole and turn. This should release the locking mechanism and allow you to open the cover.
Another way to open a locked tonneau cover is by using a paperclip or other small metal object. Insert the metal object into the keyhole and push down on the locking mechanism. This should release it and allow you to open the cover.
If neither of these methods work, you may need to call a locksmith or take your vehicle to a dealership for assistance.
How Do You Open a Tonneau Truck Cover?
There are a few different ways to open a tonneau truck cover, depending on the type of cover you have. If you have a soft cover, you can simply unzip it and fold it back. If you have a hard cover, you will need to unlatch it and either fold it back or remove it entirely.
Some covers also come with built-in gas struts that make opening and closing them easier.
What Do You Do If Your Tailgate Won’T Open?
If your tailgate won’t open, there are a few things you can try to fix the issue. First, check to make sure that the tailgate is unlocked. If it is locked, unlock it and try opening the tailgate again.
If the tailgate still won’t open, there may be an issue with the latch or hinges. Try lubricating them with WD-40 or another lubricant. If that doesn’t work, you may need to replace the latch or hinges.
How Do You Unfold a Tonneau Cover?
Assuming you have a hard tonneau cover:
To open, first unlatch the rear clamps (or whatever system is used to secure the cover at the tailgate). With the rear clamps released, you should be able to open the cover about halfway.
At this point, you can either release the front clamps or prop open the cover with something like a broom handle. Once completely unfolded, make sure to secure any loose straps so they don’t flap in the wind while driving.
Conclusion
If you have a truck with a tonneau cover and the tailgate won’t open, there are a few things you can do to try to fix the problem. First, check to see if the tonneau cover is locked. If it is, unlock it and try again.
If that doesn’t work, try opening the cover from the inside. Sometimes the latch can get stuck and needs to be released from the inside. If neither of these solutions works, you may need to remove the tonneau cover completely in order to access the tailgate.