1. Before you start, make sure that the cover is properly sized for your truck bed. You can do this by measuring the length and width of your truck bed and comparing it to the dimensions of the tonneau cover.
2. Once you have confirmed that the cover is the right size, clean the surface of your truck bed with a mild soap and water solution.
This will help ensure that the cover adheres properly to the bed liner.
3. Next, remove any debris or objects from inside the truck bed so that they don’t become caught underneath the tonneau cover when you’re installing it.
4. To begin installation, align one end of the tonneau cover with the front edge of your truck’s bed.
Then, use clamps or another type of fastener to secure it in place along this edge. Repeat this step for the opposite end of the cover.
Truxedo Lo Pro Tonneau Cover Install on Silverado with a Bed Liner
- Unroll the tonneau cover and place it over the bed of the truck
- Align the front of the cover with the cab of the truck and position it so that it is centered over the bed
- Pull the cover towards the rear of the truck bed until it is fully extended
- Secure the front of the cover to cab with straps or latches provided
- Repeat steps 2-4 for each side panel until all four panels are in place
- Fasten side panels together at center using snaps, Velcro, or other fasteners provided
How to Install Tri Fold Tonneau Cover With Bed Liner
Installing a tri fold tonneau cover with bed liner is a great way to protect your truck’s cargo from the elements. Here are some tips on how to do it:
1. First, you’ll need to remove the old bed liner, if there is one.
Use a putty knife or screwdriver to pry it up and then pull it off in sections. If the adhesive is stubborn, you can use a heat gun to loosen it.
2. Once the old bed liner is removed, clean the surface of the truck bed with soap and water.
Make sure it’s completely dry before proceeding.
3. Next, unroll the new bed liner and place it in position on the truck bed. Start at the front and work your way back, smoothing out any wrinkles as you go.
4. Once the new bed liner is in place, trim off any excess material around the edges of the truck bed. Then, use a utility knife or scissors to cut slits into the liner wherethe folds will be made. This will help prevent bunching when you fold up the cover later on.
5 . Now it’s time to installthe tri fold tonneau cover itself! Start by attachingthe front brackets according to their instructions .
Then do likewise withthe rear brackets . Be sure that they’re both centered on their respective sides ofthe truck before movingon . Fold up each sectionof coverand secureitin placewith its Velcro straps .
That’sit-you’re alldone !
How to Install Tonneau Cover Rails
Tonneau cover rails are an important part of any tonneau cover installation. Without the proper rails, your cover will not be able to function properly. Here are a few tips on how to install your tonneau cover rails:
1. Make sure that you have the correct size rails for your specific tonneau cover. Rails come in different sizes and lengths, so it is important to get the right ones for your application.
2. Once you have the correct size rails, lay them out on a flat surface.
If they are not pre-drilled, drill holes at each end of the rail using a drill bit that is slightly smaller than the bolts that will be used to attach the rails to the truck bed.
3. Next, position the rails on top of the truck bed so that they are evenly spaced and parallel with each other. Use a tape measure to make sure that they are positioned correctly before drilling pilot holes into the bed of the truck.
Be careful not to drill through any wiring or lines that may be running underneath the truck bed!
4. Finally, bolt the rails into place using nuts and bolts (or screws) that are appropriate for your particular application. Make sure that everything is tightened down securely before adding your tonneau cover and enjoying increased protection for your cargo!
Can You Install a Tonneau Cover With a Bedliner
If you have a truck with a bedliner, you may be wondering if you can install a tonneau cover. The answer is yes! You can install a tonneau cover with a bedliner, and it can actually be a pretty easy process.
Here’s what you need to know:
1. Tonneau covers come in two different styles: hard and soft. Hard covers are more durable and offer more protection from the elements, but they’re also more expensive.
Soft covers are less expensive and easier to install, but they don’t offer as much protection.
2. When installing a tonneau cover, it’s important to make sure that the cover is compatible with your bedliner. Some covers will work with any type of bedliner, but others are specific to certain brands or styles.
3. Most tonneau covers attach to the side rails of your truck bed using clamps or straps. Some models also require drilling into the side rails for installation. If you’re not comfortable doing this yourself, there are plenty of professional truck accessory shops that can do it for you.
4. Once your tonneau cover is installed, be sure to test it out before hitting the road.
How to Cut Bed Liner for Tonneau Cover
If you’re looking to protect your truck’s bed and want the added benefit of a roll-up tonneau cover, then you’ll need to cut your bed liner to fit. Here’s how to do it:
1. Measure the length and width of your truck bed.
You’ll need to add about 2 inches to each measurement to account for the lip of the tonneau cover.
2. Cut your bed liner material to size using a utility knife or razor blade. Be sure to make straight cuts so that the liner will lay flat in your truck bed.
3. Place the liner in your truck bed and trim off any excess material around the edges. Again, be sure to make straight cuts so that everything looks neat and tidy.
4. That’s it!
Your truck is now protected from scratches, dings, and dirt – not to mention, it looks great too!
Tonneau Cover Installation Video
A tonneau cover is a great way to keep your truck bed and cargo protected from the elements. But before you can enjoy the benefits of your new cover, you need to install it properly. This video will show you how to install a tonneau cover on your truck in just a few easy steps.
First, you’ll need to remove any existing bed liner or other material from the truck bed. This will ensure that the tonneau cover can be properly installed and will provide the best possible fit.
Next, you’ll need to measure the truck bed so that you can select the appropriate size tonneau cover.
Once you’ve found the perfect fit, it’s time to start installing the cover.
The first step is attaching the side rails to the brackets that are already installed on your truck bed. Once those are in place, you can then attach the front and rear bows of the tonneau cover to those same brackets.
Finally, all that’s left is to secure the tarpaulin over top of everything and zip it up tight!
With these simple instructions, you’ll have your new tonneau cover installed in no time flat!
Credit: www.dualliner.com
Can I Install a Tonneau Cover Myself?
Installing a tonneau cover is a great way to protect your gear from the elements and keep your truck bed looking sharp. But if you’ve never installed one before, the process can seem a bit daunting. Never fear!
With these simple steps, you’ll have your tonneau cover installed in no time.
1. gather your tools and materials. You’ll need a tape measure, drill, screw gun, screws, and of course, your tonneau cover.
Make sure you have everything you need before you get started so you don’t have to stop in the middle of the job.
2. measure twice, cut once. Before you start drilling any holes, double check your measurements to make sure everything will line up properly.
Once you start drilling, there’s no going back!
3. mark your holes. Use a pencil or marker to mark where you’ll be drilling on both the truck bed and the tonneau cover itself.
This will help ensure that everything lines up perfectly when it comes time to install the screws.
4 .drill away!
Carefully drill through both the truck bed and tonneau cover at each of your marked locations using an appropriately sized drill bit for your screws . Be careful not to damage anything as you’re drilling through – use gentle pressure and go slowly . If everything goes according to plan ,you should now have a series of matching holes in both surfaces that are ready for screws .
5 .time to install those screws! Line up the holes in the truck bed with those in the tonneau cover ,and then start screwing them together using your drill/screw gun . Start with just a few screws at each end so that things are lined up correctly ,then add more as needed until all of the holes are filled . At this point ,your tonneau cover should be securely attached to your truck !
How Do I Stop My Tonneau Cover from Leaking?
If you have a tonneau cover on your truck, you may have noticed that it tends to leak. While this can be frustrating, there are a few things you can do to stop the leaking.
First, check the seal around the perimeter of the cover.
If it is not tight, use a screwdriver or another tool to tighten it. You may also want to add some sealant around the edges of the cover to create an additional barrier against leaks.
Another option is to purchase a tonneau cover with a built-in drain system.
This will allow any water that gets past the seals to drain away from your truck bed, preventing it from pooling and causing leaks.
Finally, make sure that you regularly clean and maintain your tonneau cover. This will help extend its lifespan and prevent any build-up of dirt or debris that could contribute to leaks.
Do You Need Bed Rail Caps for a Tonneau Cover?
Most tonneau covers come with built-in bed rail caps, but there are a few brands that don’t. If your tonneau cover didn’t come with bed rail caps, you can usually purchase them separately. Bed rail caps protect the rails from weathering and wear and tear, and they also give the truck a finished look.
How Do You Install a Tri Fold Truck Bed Cover?
Assuming you would like a detailed, step-by-step guide on how to install a tri-fold truck bed cover:
1. Before you begin, make sure you have all the necessary tools and parts. You will need a drill, screws, washers, wire cutters, and of course the tri-fold truck bed cover.
Also check to see if your vehicle has any pre-drilled holes; if so, you won’t need the drill.
2. Begin by opening up the cover and laying it out in the bed of your truck. If there are any crossbars or side rails, make sure they are properly positioned before proceeding.
3. Next, take the provided mounting brackets and attach them to the inside lip of the truck’s bedside using either screws or bolts (again, depending on whether or not your vehicle has pre-drilled holes). Do this for both sides of the truck bed.
4. Once the brackets are in place, carefully lift up the cover and position it so that the front edge is flush with the cab of your truck.
Make sure that it is level before proceeding to step 5.
5a. If your model has wing seals: Take each wing seal and peel off one side of the adhesive backing strip; then press it into place along the corresponding side edge ofthe cover (one seal per side).
Make sure that they are properly aligned before moving on to step 5b.
5b. If your model does NOT have wing seals: Skip this step!
Proceed directly to step 6 below.. Now would be a good time to test fit everything before permanently attaching anything.
.6 With someone holding up one end ofthecover(nearthe cab), start at either endoftherailand slowly workyourwaytothecenterofthetruckbed while attaching each railtoitsmounting bracket using eitherscrewsor bolts (dependingonwhetherornotyourvehiclehaspre- drilledholes)..Tighteneachoneasyougountilallaresecuredinplace..Ifeverythinglookslevelandalignedproperly,.you can nowmove ontoStep7 below..7 Dependingonyourmodel,.youwillnowhavetoplaceeitherendcapsonoraero/ fairingontopofthecoveratthispointintheinstallation process.
Conclusion
Assuming you want a summary of the blog post and not just the topic:
A tonneau cover is a great way to keep your belongings safe and dry while driving. But if you have a bed liner, installing the cover can be a bit tricky.
Here are some tips on how to install a tonneau cover with a bed liner:
1. First, remove any objects from your bed that could get in the way of the installation, such as cargo racks or tie-downs.
2. Next, clean the area where the cover will be installed with soapy water to remove any dirt or debris.
3. Then, line up the rail system of the cover with the rails of your truck bed, and start attaching them together using the provided hardware.
4. Once all four rails are attached, you can then snap on the tarpaulin cover itself. Make sure it’s tight and secure before heading out on your next road trip!