To measure for a boat cover, first determine the size and shape of the boat. Then, using a tape measure, measure the length from the tip of the bow to the stern. Next, measure the width at the widest point of the hull.
Finally, measure the height from the deck to the top of the cabin.
- Decide which type of boat cover you need
- Measure the length of your boat from the tip of the bow to the stern
- Measure the beam width of your boat at its widest point
- Determine if you need a trailerable or non-trailerable cover by measuring the height of your boat from the waterline to the highest point on the boat, including any antennas or other protrusions
- Choose a cover with appropriate dimensions based on your measurements
Measuring for a boat cover
How Do You Measure a Boat Canvas?
If you’re looking to measure a boat canvas, there are a few things you’ll need to keep in mind. First, you’ll need to know the dimensions of the canvas itself. This can usually be found on the label or tag attached to the canvas.
Next, you’ll need to take into account the amount of stretch that the canvas has. This will affect how tight or loose the fit is when measuring. Finally, consider any hardware that may be attached to the canvas, such as snaps or grommets, which can add extra bulk and affect the overall measurements.
To get started, first lay the canvas flat on a surface. Then, use a measuring tape to measure from one side of the canvas to the other at both the top and bottom. Be sure to note down these numbers so you don’t forget them!
Next, measure from side-to-side at boththe left and right edges of the canvas. Again, make sure to write these numbers down for reference later.
Now it’s time to calculate the stretch factor.
To do this, simply take one of your side-to-side measurements and divide it by one of your top-to-bottom measurements. For example, if your canvas is 10 feet wide by 8 feet tall, then its stretch factor would be 10/8=1.25 (10 divided by 8 equals 1 with a remainder of 2). In other words, for every 8 inches of height, this particular piece of fabric stretches an additional 1 inch horizontally (or vice versa).
Now that you have all your measurements and calculations completed, it’s time to put them all together! To get your final measurement for how wide or tall your boat cover should be), simply multiply each original measurement by 1 plus whatever percentage increase is necessary due to stretching (in our example above , we would multiply everything by 1 . 25 since our stretch factor was 1 . 25 ). So using our earlier example again , a 10 foot wide piece of fabric that’s been stretched 25% would become 12 .
5 feet wide ( 10 x 1 . 25 = 12 . 5 ). And finally , don’t forget about those pesky hardware attachments ! If they’re present , be sure add enough extra fabric around them so they don’t rip through when putting your cover on or taking it off .
Happy measuring!
How Do I Measure My Boat?
There are a few different ways that you can measure your boat. The most common way is to use a tape measure. You will need to measure the length and width of your boat.
You will also need to measure the height of your boat. Another way to measure your boat is to use a measuring wheel. This is a tool that you can roll along the ground to get an accurate measurement of your boat.
How Do You Measure a Boat Top?
When you are ready to measure your boat top, you will need a few supplies. You will need a measuring tape, a level, and something to mark the measurements with. You will also need a friend to help you measure, as it can be difficult to do it yourself.
Start by measuring the length of the boat from the very front to the very back. Then, measure the width of the boat at its widest point. Make sure to write down these numbers so that you don’t forget them!
Next, you will need to measure the height of the boat top from the deck up. To do this, first find the centerline of the boat and make a mark on each side where the deck meets this line. Then, using your measuring tape and level, measure straight up from each mark until you reach the highest point of the boat top.
Again, be sure to write down these numbers so that you don’t forget them!
Now that you have all of your measurements, you can start figuring out how big your new boat top needs to be. Keep in mind that you will want to leave some extra fabric so that you can sew it or secure it in place once it is made.
Once you have determined how big your new top needs to be, simply follow these same steps to measure and cut it out!
What is the Best Material to Make a Boat Cover Out Of?
There are many materials that can be used to make a boat cover, but the best material depends on the type of boat and the climate. For example, if you have a small fishing boat that you use in mild weather, you might want to use a tarp or canvas. However, if you have a large yacht that you use in tropical climates, you might want to use a UV-resistant fabric such as Sunbrella.
Ultimately, it is important to consult with a professional before making your final decision.
Credit: www.youtube.com
Exact Fit Boat Covers
If you have a boat, then you know how important it is to keep it protected from the elements. A boat cover is essential for keeping your investment in good condition. But not just any cover will do – you need an Exact Fit Boat Cover that’s specifically designed for your make and model of boat.
Why bother with a custom-fit cover? Because a properly fitting cover will do a better job of protecting your boat from sun damage, wind damage, and even theft. Loose-fitting covers can blow off in high winds, leaving your boat exposed to the elements.
And if your cover is too small, it can put stress on the fabric and cause premature wear.
Exact Fit Boat Covers are made to order based on the make, model, and year of your boat. That means they’ll fit like a glove – no more struggling to stretch a too-small cover over your boat or worrying about it blowing off in the wind.
And because they’re custom made, you can choose from a variety of colors and materials to get the perfect look for your boat.
Whether you want a simple mooring cover or a full-blown storage cover, Exact Fit has you covered. So don’t wait – order your custom-fit Exact Fit Boat Cover today!
Boat Measurements Explained
Boat measurements can be confusing, but they don’t have to be! Here’s a quick guide to some of the most common boat measurements you’ll come across.
Length: This is the overall length of the boat, from bow (front) to stern (back).
It’s usually measured in feet or meters.
Width: This is the distance from one side of the boat to the other. Again, it’s usually measured in feet or meters.
Draft: This is the depth of water that your boat needs in order to float safely. It’s important to know your draft when docking or entering shallow areas. Draft is typically measured in feet or meters.
Beam: Beam is similar to width, but it specifically refers to the widest part of the boat. This measurement is important when determining how stable your vessel will be on the water. Beam is typically measured in feet or meters.
How to Measure a Boat Width
One of the most important dimensions on a boat is the width, which is also sometimes referred to as the beam. The width of a boat is critical in determining how stable it will be on the water and how much weight it can safely carry. Measuring the width of a boat is relatively simple and only requires a few tools.
To measure the width of your boat, you will need:
-A tape measure
-A level
-An assistant (optional)
Instructions:
1. Begin by measuring from the widest point on one side of the boat to the widest point on the other side.
Use a tape measure for this step and record the measurement. This is typically done at the midpoint of the boat, but can be done at any point along its length. If you have an assistant, they can help hold one end of the tape measure while you take your reading.
2. Once you have recorded this first measurement, use a level to make sure that your tape measure was level when taking your reading. The level should read zero when placed horizontally across your recording marks. If it does not, simply adjust your marks until they are perfectly level with each other and re-measure to confirm your new reading before proceeding to step three.
Note that some boats have asymmetrical hulls which can make this step more difficult; in these cases, simply do your best to ensure that the tape measure is as close to level as possible before proceeding to step three. Remember that precision is key when measuring something as important as a boat’s beam!
3. Finally, average out your two measurements (the original one and levelled one) by adding them together and dividing by two .
This final number is likely going to be different than either individual measurement , but will provide you with a more accurate representation of your boat’s true beam width . And there you have it – now you know how to accurately measure a boat’s beamwidth !
Conclusion
If you’re looking to purchase a boat cover, it’s important to know how to measure for one. The first step is to measure the length of your boat from the tip of the bow to the stern. Next, you’ll need to measure the beam width of your boat.
This is the distance from one side of the boat to the other at its widest point. Finally, you’ll need to take into account any additional features on your boat that might impact the size or fit of a cover, such as an extended swim platform or T-top. Once you have these measurements, you can start shopping for a cover that will fit your boat perfectly.